This is the replacement elbow that attaches the Simple Cushion to the ComfortLite and ComfortLite 2 Nasal Interface. Return On Warranty Issues Only
Specifications
CPAP.com always offers these services:
8 am to 10 pm CST Toll Free Phone and Email Support
24 hour access to our CPAPtalk.com Support Forum
Learning Center for information on sleep apnea and cpap equipment
Consumer Purchasing Trends Reports
Product Evaluation Results from our Product Challenges
Warranty Services for all items purchased through CPAP.com
Insurance Compliant Invoices
Free Prescription Request System
Manufacturer Note:
We are only authorized to sell and ship Philips Respironics products to end-users residing in the United States.
Philips Respironics recommends that new patients purchase their devices, masks and initial accessories from a homecare company that can provide an individualized patient equipment set-up, clinical and after-sales support, and a program to assist patients with therapy success.
"The locking "finger" that retains the elbow on the headset is always breaking. It is the weakest part of the whole mask. The vent holes should be aimed upward, not forward. My wife doesn't like the cold breeze on her when I sleep on my side, facing her."
Homerun !
John M, CO – January 11, 2012
"For over 6 years I have been asking my local O2 provider if I can buy just the needed cushions and elbows. No way! You have to buy the entire headgear, face mask and the Whole Nine Yards. And then, they don't deliver as promised. Frustrating! CPAP.com carried exactly (& only) the parts I needed, and sent them in record time. I'm a new favorite customer of CPAP.com"
Paul L, AB – January 10, 2012
"this is a very good product and you give very good service"
poor design
Barbara A, SC – August 06, 2011
"I think some work needs to go into this piece, I have to replace it about every 3 months, it breaks at the same place everytime"
Jean C, ON – June 26, 2010
"I just bought this to have a spare on hand. It would seem that it could easily be lost, switching between the various interfaces with this mask."
The Angle Adjuster controls the tilt of the cushion to the face and the twist Vertical Adjuster helps position the cushions relative to the length of your face and nose.
Can you explain the Angle Adjuster in more detail?
If you have seen a picture of the ComfortLite 2, you will notice that the cushions connect to a tube. The tube is suspended from the center of the headgear where the Angle Adjuster is. By squeezing the blue tabs on each side of the Angle Adjuster, you are able to change the angle of the tube (and cushion) either closer to or away from the face.
What does the Vertical Adjuster do?
As you look at the mask picture, you’ll see a circular blue knob at the top of the tube connected to the ComfortLite 2 cushion. By twisting the knob, you either extend or retract the length of the tube.
What is the function of this Halo headgear Crown Swivel at the top of the head?
The swivel helps to manager your longer 6 foot hose with a 180 degree swivel which moves from one side to the other in an arch above your crown. The sleeve your hose attaches to swivels 360 degrees also.
Why is the Crown Swivel attached to the Halo headgear?
Respironics trials found that the short and long hose easily get wrapped up around the active sleeper if not anchored. Also, the anchored swivel helps to absorb the movement of the long hose as you move. Masks often lose their seal because the weight of the long hose tugs at the mask or cushion, which is prevented by the Crown Swivel design.
Does the ComfortLite 2 work for people who sleep on their sides?
Yes, the ComfortLite 2 is designed to accommodate side sleeping by providing an assembly and interface that is centered over the nose and up the center of the head.
Is it easy to take the ComfortLite 2 mask on and off?
Yes, it is very easy. To take the ComfortLite 2 off, simply grasp the angular adjustment area and pull the mask forward then lift upward. This way, the mask can be placed on and taken off without changing any of the adjustments.
There is air coming out of the elbow on the cushion – is this OK?
Yes, this is air coming from the exhalation valve. This leak is intentional and removes CO2 from the mask. Never cover or attempt to block these holes. Your CPAP unit is designed to still provide your therapy pressure.
Once I have the correct angle for one cushion, will it be the same for all?
You will have slightly different angular adjustments when using the Simple Cushion vs. the Pillows or Direct Seal cushions.