IntelliPAP Integrated Heated Humidifier

Water–Resistant Water Chamber Holds Enough Water to Last Eight Hours

The device is water-resistant and has a stainless steel heat transfer plate and a Lexan–constructed (polycarbonate resin thermoplastic) water chamber. The water chamber is designed to hold enough water for eight hours—a full night’s sleep.

Eliminates the Need for Bulky Power Adapters and Additional Hoses

There’s no need for bulky power adapters or extra hoses that take up space since the unit is powered by docking to the CPAP machine.

What’s Included:

• Humidifier
• Chamber

Operating Atmospheric Pressure: 50 to 106 kPa

Standards Compliance:

This humidifier is designed to conform to the following standards:

• IEC 60601-1 General Requirements for Safety of Medical Electrical Equipment
• EN ISO 17510-1 Sleep Apnea Breathing Therapy Devices

Type of Protection Against Electric Shock: Class II Equipment

Degree of Protection Against Electric Shock: Type BF Applied Part

Equipment Type: IPX1: Drip Proof Equipment

EMC Operation: Continuous

Electromagnetic Compatibility: The device meets the requirements of EN 60601-1-2, 2nd edition.

Disposal: When necessary, dispose of the humidifier in accordance with local regulations.

Maximum Fill Level Tips

• Do not fill the water tank above the maximum fill line. Damage to the humidifier or therapy device may occur. If the water tank is overfilled, water may leak out of the tank inlet (located on the back of the tank) when installing the tank lid.
• Use only room temperature distilled water in the tank. Do not put any chemicals or additives into the water. Possible airway irritation or damage to the water tank may result.
• Remove the tank, empty all water, and replace the empty tank before transporting the humidifier base.
• Do not attempt to fill the water tank while it is inside the humidifier.
• To avoid spilling, do not disconnect the humidifier from the therapy device with water in the tank. Remove the water tank from the humidifier before disconnecting the therapy device.
• Do not turn the humidifier on without the water tank installed. The Humidifier number setting must remain on 0 if there is no water in the water tank.
• The humidifier door must be set in the open position before removing the water tank. Do not remove the water tank without making sure that the humidifier door locks into the open position.
• Do not move the humidifier while the water tank has water in it.

Manufacturer Warranty

DeVilbiss offers a 3 (three) year manufacturer warranty on IntelliPAP Humidifier orders placed on or before 2/14/2012.

• If the order date for an IntelliPAP Humidifier is 2/15/2012 or later it carries a 5 year manufacturer warranty.
• If the order date for an IntelliPAP Humidifier is 2/14/2012 or earlier it carries a 3 year manufacturer warranty.

DeVilbiss offers an industry leading 5 (five) year manufacturer warranty on IntelliPAP machine orders placed on or after 2/15/2012.

• If the order date for an IntelliPAP machine is 2/15/2012 or later it carries a 5 year manufacturer warranty.
• If the order date for an IntelliPAP machine is 2/14/2012 or earlier it carries a 3 year manufacturer warranty.

Important Note: If using the heated humidifier with the IntelliPAP series, the units cannot be operated from DC power. A modified sine wave inverter of at least 120VAC is necessary to power both the machine and humidifier from a DC power source. CPAP.com carries two inverters that would be compatible:

300 Watt DC to AC Power Inverter

400 Watt DC to AC Power Inverter

Bacteria Filter

A bacteria filter will not install directly to the air outlet port on the IntelliPAP Heated Humidifier. The filter is too bulky and there is not enough space. IntelliPAP humidifier owners can order the FlexiTube Angle Adapter for CPAP and BiPAP Machines to provide a spacer between the humidifier and the bacteria filter. Your CPAP hose can then fit onto the other end of the bacteria filter.