Important: Mask and Tube Compatibility

Unlike other machines which have universal hoses compatible with any mask, the AirMini™ is ONLY available in package configurations with the specific masks and corresponding tubes.

The following masks have unique AirMini™ mask setups which are designed to correspond with the travel CPAP device:

• AirFit™ N20 Nasal Mask
• AirFit™ F20 Full Face
• AirTouch™ F20 Full Face
• AirFit™ P10 Nasal Pillow

Please Note: The unique venting system built into the included mask has been created to help decrease noise when paired with the HumidX™ humidification component. The design impacts the elbow and the CPAP tube connection, thus the above masks are not compatible on their own if used with the AirMini™ CPAP machine. This purchase includes the proper tube and elbow connection, providing all components needed to operate the system.

No other hoses or accessories (including humidifiers) are compatible with this device.

Important: Return Policy

ResMed offers a 30 day guarantee on the mask purchased with the AirMini™ to allow the user to try one of the other compatible masks. ResMed does NOT offer non-warranty returns for the machine itself.

FAA Approved

The AirMini™ meets Federal Aviation Administration (FAA) requirements. If using the device while on an airplane, disconnect from Bluetooth by pressing down on the Bluetooth button for a minimum of 10 seconds. The light will release a white flash when airplane mode has been reached.

Tips to Pair the Device with the AirMini™ By ResMed App

1. Download the (free) AirMini™ By ResMed App
2. Open the app and agree to the Terms & Conditions Please Note: No signup or personal information is required.
3. Verify the Bluetooth feature on the smart phone or tablet have been enabled.
4. Gently press the Bluetooth button found on the front of the machine until a small blue light begins to blink.
5. Opt to scan or manually enter the key code on the bottom of the machine.
6. b Begin following the setup instructions: Select the mask being used with the device and watch instructional clips.
7. Move between three screens to view data.
   • The Dashboard Screen shows personal usage data.
   • The Sleep Screen allows the user to turn the machine On or Off, run Mask Fit, or adjust machine settings such as Ramp, Pressure Relief, and SmartStart/Stop.
   • The More Screen shows preferences and user guides.

Humidification Tips: HumidX™ versus HumidX™ Plus

It is recommended to start with HumidX™ when first adding humidification to the device. If the moisture level is not sufficient due to environment, use the HumidX™ Plus unit to increase moisture.

The AirFit™ N20 and AirFit™ P10 masks are compatible with ResMed's HumidX™ and HumidX™ Plus waterless humidification units. Please Note: The AirFit™ F20 and AirTouch™ F20 tubes are NOT compatible with the HumidX™ units. Also, it is important to replace the HumidX™ units 30 days after the package is opened.

Tips to Assemble and Disassemble HumidX™ Units

• Assembly: To assemble the HumidX™ device, gently twist the bulbous connection point on the CPAP tube to disconnect the hose. With the blue base pointed downward, secure the unit on the end of the connection. Then, connect the tube pieces together and lock into place.
• Disassembly: To disassemble the HumidX™ device, twist and disconnect the bulbous connection on the hose. Remove the HumidX™ after 30 days and replace with a fresh unit.

Cleaning Tips

Disassemble all parts including the HumidX™ when preparing to clean the mask, accessories, and device.

• AirMini™ Tubing: Evaluate the tube for holes or signs of wear and wash at least once per week. Submerge the tube in warm water with mild detergent. Rinse thoroughly and allow to air dry away from direct sunlight. Tubing should be replaced every 6 months.
• N20 and F20 Connector: Wash the F20 connector daily with warm water, mild soap, and a soft bristle brush to thoroughly clean the vents. Rinse well to remove all soap and allow to dry away from direct sunlight. Do Not place in the dishwasher or washing machine. The connector should be replaced every 6 months.
• HumidX™ | HumidX™ Plus: Check daily for signs of damage or blockage. Replace the unit 30 days after the HumidX™ package is opened. DO NOT wash the HumidX™ or HumidX™ Plus.
• Filter: The filter is disposable and is NOT intended to be washed. Replace the filter every 6 months. Check for particle blockage often.
• Machine: Use a dry cloth once a week to wipe away dirt from the outside of the machine.